Yuan Class AIP & Kilo Submarine Thread

schenkus

Junior Member
Registered Member
Still need steam generator and and condenser, you can avoid using pump but there is no way to avoid steam generator and condenser because it is rankine cycle after all And pump it still needed for the steam generator loop it is shown on right hand corner
The primary loop does not need pump

A (perhaps stupid) question: could one use a sterling engine instead of a turbine and not need any steam at all ?
 

taxiya

Brigadier
Registered Member
A (perhaps stupid) question: could one use a sterling engine instead of a turbine and not need any steam at all ?
In theory, you can. You can build the hot end of Stirling engine into part of the 2nd loop as the heat exchanger. I have heard such proposal.

In practice, maybe nobody want it for reasons:
  1. Stirling engine use permanently gaseous working fluid. It is worse than liquid in transporting heat energy, meaning lower overall efficiency.
  2. Stirling engine is piston engine running at much lower RPM. Lower frequency of noise travels longer range than high frequency noise of the steam turbine.
  3. Stirling engine's pistons moves in a linear vector back and forth. It create strong vibrations, the bigger the piston is, the stronger, this is related to 2nd point, but not limited to noise.
  4. Stirling engine is big and bulky, lower power density compared to steam turbine.
  5. Practical Stirling engine has pumps in the loop. The working gas need to be cooled by ambient air or sea water in a sub. That circulation need pumps. It does not eliminate pumps more than this nuclear AIP who only has pump in the 3rd loop, the 1st and 2nd loop are natural circulated.
  6. Stirling engine has much lower efficiency than steam turbine. The nuclear AIP's reactor has already sacrificed efficiency for noise, size and safety reasons, using Stirling engine will make it useless.
There is nothing bad with steam or turbine although they sounds old because they were broadly used for a long time. Stirling engine is nothing new, nor technically superior.
 

schenkus

Junior Member
Registered Member
In theory, you can. You can build the hot end of Stirling engine into part of the 2nd loop as the heat exchanger. I have heard such proposal.

In practice, maybe nobody want it for reasons:
  1. Stirling engine use permanently gaseous working fluid. It is worse than liquid in transporting heat energy, meaning lower overall efficiency.
  2. Stirling engine is piston engine running at much lower RPM. Lower frequency of noise travels longer range than high frequency noise of the steam turbine.
  3. Stirling engine's pistons moves in a linear vector back and forth. It create strong vibrations, the bigger the piston is, the stronger, this is related to 2nd point, but not limited to noise.
  4. Stirling engine is big and bulky, lower power density compared to steam turbine.
  5. Practical Stirling engine has pumps in the loop. The working gas need to be cooled by ambient air or sea water in a sub. That circulation need pumps. It does not eliminate pumps more than this nuclear AIP who only has pump in the 3rd loop, the 1st and 2nd loop are natural circulated.
  6. Stirling engine has much lower efficiency than steam turbine. The nuclear AIP's reactor has already sacrificed efficiency for noise, size and safety reasons, using Stirling engine will make it useless.
There is nothing bad with steam or turbine although they sounds old because they were broadly used for a long time. Stirling engine is nothing new, nor technically superior.

It seems sterling engines are used in the swedish AIP system - would this have the same problems or is there some basic difference I'm missing ?
 

taxiya

Brigadier
Registered Member
It seems sterling engines are used in the swedish AIP system - would this have the same problems or is there some basic difference I'm missing ?
No, there is nothing wrong or that you are missing with Stirling engine. Swedish, Chinese and Japan all are using it.

Before this nuclear AIP setup, Stirling is the most accessible AIP tech China has through buying from Swedish. Germany was very good in Fuel-cell which is even quitter, they don't need Stirling. Japan's sub are really big and need long endurance, Stirling is better choice, besides (at least German) fuel-cell sub has to be cut open when servicing the fuel-cells.

With the new nuclear plant, the equation has changed for PLAN at least, that's all.
 

by78

General
Another head-on view...

(1915 x 2048)
47839464602_ac950de0c1_k.jpg
 
Top